Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateWhy Rochester Homeowners Choose Ghost Controls Gate Repair
We provide independent Ghost Controls gate repair service in Rochester, NY, for the solar and low-voltage swing gate operators that show up on a lot of local driveways and side yards. What makes our Ghost Controls work different is that we treat the operator as a system: charger, battery, board, arm, remote. We test all of it under load before we name a failure. We’re a gate-only shop in Rochester, not a fence company that squeezes in openers. We’re not affiliated with, authorized by, or endorsed by Ghost Controls. We’re an independent service provider, and we tell you that up front. Call (866) 942-8010 for a free estimate.
Why Trust Rochester Gate Repair for Your Ghost Controls Gate Repair?
Ghost Controls units are mostly homeowner-installed, and that shapes how they fail. The hardware itself is straightforward. What goes wrong usually comes from installation geometry, solar charging, or battery health under load. Our technicians have up to 10 years of experience, and they’ve worked on enough of these systems to know the difference between a bad battery and a board that’s not charging it.
We diagnose these operators by reading the actual symptoms: sluggish travel, gates that stop mid-cycle, remotes that stop responding after a battery change. We use quality replacement parts that fit Ghost Controls equipment, and we choose parts by compatibility, not by what’s sitting on a shelf. Our parts practice is warranty-safe by design. We don’t cut wires, bypass safety edges, or install a component that doesn’t match the system’s electrical spec, because that’s how a manufacturer warranty claim gets denied. For a Rochester homeowner, that discipline is the difference between a fix and a repeat visit next season.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Common Ghost Controls Gate Repair Problems We Fix in Rochester
These are the failure modes we see most on Ghost Controls operators around Rochester. They’re described by symptom and cause, not by part number.
- Solar charge loss and battery degradation. The gate moves slower than it used to, or stalls on the second or third cycle of the day. A sealed lead-acid battery that’s aging or holding charge poorly will pass a no-load voltage check and still fail under the pull of the arm. Reduced sun hours through a Rochester winter shorten the charging window and expose a battery that was already getting weak.
- Control board faults after voltage spikes. A nearby lightning strike or a surge on the low-voltage side can leave the board in a state where the gate sits stuck open or ignores the remotes entirely. Board-level diagnosis matters here, because a dead board and a dead battery can produce the same symptom to a homeowner.
- Limit switch and arm binding on homeowner-installed kits. When the operator arm geometry isn’t set correctly on install, the gate binds partway through travel and the limit switches lose their reference. The operator reads that as an obstruction. The fix is usually alignment and switch position, not a new arm.
- Remote and keypad pairing loss. After a board reset or a battery swap, paired remotes and keypads can drop out. Often the hardware is fine and the pairing just needs to be redone after the system stabilizes. Weather-seal failures on the control box are a common reason that pairing gets lost in the first place.
- Seasonal freeze-thaw drag. Lake-effect snow and repeated freeze-thaw cycles from Lake Ontario work a gate loose at the hinge and post foot. Wood swells, hinges seize, and a sagging gate drags on a heaved concrete apron. Sometimes a Ghost Controls operator is diagnosed as failing when the real problem is a gate that no longer swings freely.
A Ghost Controls AXS swing gate that opens sluggishly or stops mid-travel often traces back to a failing battery or a solar panel no longer keeping up, especially after a cloudy stretch. A qualified technician typically tests battery voltage under load, checks the charge controller output, and verifies the limit switches and arm alignment before recommending a battery or control board replacement.
Ghost Controls Parts & Our Repair-vs-Replace Approach
We repair and service Ghost Controls equipment with quality parts that fit it. That includes OEM control boards, arms, and solar charge components where the original spec calls for them, and quality aftermarket batteries and remotes as a cost-effective alternative when we’ve confirmed compatibility with the system. We don’t claim to stock or carry OEM or genuine Ghost Controls parts, and we’re not a Ghost Controls dealer. We source what the job needs.
Our repair-vs-replace call leans repair when the operator housing, the arm, and the gate structure are sound. If the board and the mechanicals are both failing at once, replacement is usually the better use of your money, and we’ll say so plainly. We’d rather tell you which one makes sense than sell you a control board for a system that needs a new operator. If you’re not sure which side of that line your gate is on, call (866) 942-8010 for a free estimate.
Our Ghost Controls Service Process – Step by Step
- 1
Diagnosis at the gate. We test battery voltage under load, check solar charge controller output, verify limit switch position, and watch the arm travel through a full cycle. We check the gate’s own swing and hinge condition too, since drag from a heaving post can mimic an operator fault.
- 2
Repair or install. Once we know what’s failing, we quote the job before any work starts. On a battery or board replacement we match the component to the system’s spec. On a fresh installation we set arm geometry correctly from the start, which is where most homeowner installs go wrong.
- 3
Full-cycle test. We run the gate open and closed several times, re-pair remotes and keypads, confirm the safety edges respond, and check the battery is actually taking a charge from the solar panel.
- 4
Warranty and parts record. We document what was replaced and why, so a future warranty question has a clean service record behind it. No bypassed safety equipment, no mismatched components.
See the difference
Before
After
Before
After
Before
AfterGhost Controls Products We Service & Install in Rochester
We service and install the Ghost Controls product types local owners actually have. That means the AXS Series kits (AXS1, AXS2, AXS3), the Titan Series (TITAN1 and TITAN2), and the heavy-duty dual swing kits in the TDS series. We also handle the solar and low-voltage accessory packages around them: solar panels, battery boxes, and keypads. Older Titan units that have been in service for years are common, and they’re worth a proper diagnostic before anyone writes them off. In Rochester, that seasonal charging reality matters more than it does in a place with steady sun, which is why we treat battery backup as a core part of the service, not an add-on.
We Also Service These Brands
Ghost Controls is one system we know well, but we’re a multi-brand gate shop. We also work on LiftMaster, on Mighty Mule for residential swing and slide gates, and on DoorKing for commercial and access-control systems that property managers rely on. Serving both homeowners and property managers means we’re not tied to one brand or one type of customer. If your gate system isn’t Ghost Controls, we still know how to read it.
FAQs – Ghost Controls Gate Repair Service in Rochester
No. We’re an independent Ghost Controls service provider, not an authorized dealer, and Ghost Controls has not certified or endorsed us. We repair, install, and service Ghost Controls equipment on our own as a gate-only specialist. That independence is why we can recommend the part that actually fits your system instead of being locked to one supply line.
Yes. We use quality replacement parts that fit Ghost Controls operators, including OEM control boards, arms, and solar charge components where the original spec calls for them, and quality aftermarket batteries and remotes when we’ve confirmed compatibility. We don’t claim to stock genuine Ghost Controls parts. We source what the job needs.
Most Ghost Controls repairs are completed on the first visit when the needed part is on hand, and a battery or remote swap is typically faster than a control board replacement. Diagnostics take the longest, because we test the charger, battery, arm, and switches before quoting. Call (866) 942-8010 and we’ll give you a straight answer for your gate.
We cover the AXS Series kits, the Titan Series, the TDS heavy-duty dual swing kits, and the solar and low-voltage accessory packages around them, including solar panels, battery boxes, and keypads. If you’re not sure which system you have, we can identify it at the gate during a free estimate.
Proper service shouldn’t void your warranty, and our practice is built to protect it: we use parts that match the system’s electrical spec, we don’t bypass safety equipment, and we document what we replaced. If a warranty claim comes up later, you’ll have a clean service record to back it. Call (866) 942-8010 for a free estimate.
Ghost Controls gate repair in Rochester is priced per job based on the written estimate, and the estimate is free. A battery or remote replacement is a smaller job than a control board or charge controller swap, so the range varies by what’s failing. We quote and agree the price before any work starts. Call (866) 942-8010 for an exact quote.
Sluggish or stopping travel in cold weather usually points to a battery that’s weak under load combined with reduced solar charging through a lake-effect winter. Cold reduces usable battery capacity, and shorter sun hours mean the panel isn’t replacing what the gate uses. A load test on the battery and a check of charge controller output will tell you which part is the culprit. Call (866) 942-8010 for a free estimate.
After a battery replacement, a remote that stops working is usually a pairing issue, not a dead remote. Many Ghost Controls remotes need to be re-paired to the operator after a control board reset or battery swap. If the remote still fails after re-pairing, the remote itself or the receiver is the next thing to test. Call (866) 942-8010 and we’ll sort it out.
Yes, in most cases you can add a keypad or intercom to an existing Ghost Controls system if the operator’s control board has the input for it. Compatibility depends on the specific operator and how the accessory is wired, so we confirm that before recommending anything. Call (866) 942-8010 for a free estimate.
Repair is usually worth it on a Titan operator when the housing, arm, and gate structure are sound and the fault is limited to a battery, board, or charge component. Replacement makes more sense when the control board and the mechanicals are both failing at once. We’ll tell you which side of that line your operator is on. Call (866) 942-8010 for a free estimate.
A gate that opens on its own or won’t close all the way usually traces to a limit switch that’s out of position, an arm that’s binding, or a control board that lost its reference after a surge. It can also be a rogue remote signal from a neighbor’s paired remote. Diagnosis starts with the limit switches and arm alignment, then the board. Call (866) 942-8010 for a free estimate.
Book Your Ghost Controls Service in Rochester, NY
Whether your Ghost Controls operator is stalling on a cold morning, your remote quit after a battery swap, or you’re adding a keypad or replacing a board, we’ll diagnose it properly and quote the job before we touch a wire. We work on Ghost Controls across Rochester, and we also service LiftMaster, Mighty Mule, and DoorKing. Call (866) 942-8010 for a free estimate. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Written by the team at Rochester Gate Repair.