Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateTrusted Electric Gate Repair for Rochester Homeowners
When your gate stops responding to the remote, the operator clicks and nothing moves, or the arm drags the gate halfway and stalls, that’s an electric gate problem that needs a gate specialist, not a general contractor. Electric gate repair in Rochester covers everything between the control board and the motor to the safety sensors, and it’s the work we do all day. Our technicians have up to 10 years of experience with automated gate systems, and we diagnose by system and brand rather than guessing at parts. If your gate is down right now, call (866) 942-8010. Same-day service is often available in Rochester, and we quote the price in writing before any work starts so the invoice never surprises you. From residential openers to commercial access control, we get gates back to working on the first visit.
Gate Opener Repair
Gate Opener Repair fixes the unit that does the actual driving, whether that’s the arm, the slider operator, or the control box, when the gate is sound but the opener has quit. You need it when the opener hums without moving, reverses for no reason, loses its limit settings, or the remote works only when you’re standing close. We service LiftMaster and Linear openers among the brands we know well, test the board, motor, and limits, and repair or replace based on what actually makes sense rather than what bills the most. A typical opener repair in Rochester runs $180-$420 depending on whether we’re swapping a board, a motor, or the whole unit. The written estimate sets the final price. Call (866) 942-8010 for a free estimate.
Openers That Hum but Don’t Move
A motor that runs without turning the gate usually points to a stripped gear, a failed coupler, or a limit switch out of position. We test the drive train first so we’re not selling you a motor when a gear is the real fault.
Remotes and Receivers That Lose Signal
Intermittent remotes often trace to a weak receiver, a dying battery, or interference from a nearby transmitter. We check the receiver board and re-pair or replace the remote components so the gate responds from the driveway every time.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Automatic Gate Repair
Automatic Gate Repair covers the whole system that swings or slides the gate on its own, including the operator, the safety edges, the sensors, and the linkage that ties it all together. You need it when the gate moves erratically, stops mid-travel, crushes against an obstacle before reversing, or won’t open when a vehicle pulls up. We handle both swing and slide automation and know where each system tends to fail. FAAC and BFT systems are in our regular rotation. A typical automated gate repair in Rochester runs $200-$650 depending on what the diagnostics turn up, and the written estimate sets the final price. We quote before we start. Call (866) 942-8010 for a free estimate.
Safety Edge and Obstruction Faults
A safety edge that’s damaged or misaligned can cause the gate to reverse on its own or refuse to close at all. We test the edges and photo eyes against the manufacturer’s trip specification so the gate stops correctly without nuisance trips.
Arm and Linkage Alignment
Bent arms and worn linkage make a gate labor and bind, which wears the motor out fast. We check the geometry and replace or realign the hardware so the gate travels smoothly through its full arc.
Electric Gate Motor
Electric Gate Motor work is the repair or replacement of the motor itself, the part that converts power into the push or pull that moves your gate. You need it when the motor is overheating, grinding, drawing too much current, or has quit entirely after years of daily cycles. We test motor current draw and thermal behavior rather than condemning a motor on appearance. We service motors across the residential and commercial equipment we work on, and we match the replacement to the gate’s weight and cycle count. A typical motor repair or replacement in Rochester runs $350-$900 depending on the unit and the gate. The written estimate sets the final price. Call (866) 942-8010 for a free estimate.
Motor Overheating and Thermal Shutdown
A motor that runs and then shuts down for a cool-off period is usually undersized for the gate or binding on its track. We measure the load and correct the cause before the motor fails for good.
Matching a Replacement Motor to Your Gate
Cycle count, gate weight, and duty rating all determine the right motor. We size the replacement to how your gate is actually used so the next motor lasts rather than repeats the last failure.
Gate Access Control
Gate Access Control is the system that decides who gets through, covering keypads, card readers, intercoms, and the telephone or app entry that residents and staff use. You need it when codes stop working, a keypad won’t program, a reader drops calls, or the board won’t release the gate for a valid entry. We work on DoorKing access control and the entry hardware that integrates with residential and commercial operators. A typical access control repair in Rochester runs $220-$600 depending on whether we’re reprogramming, replacing a keypad, or repairing a reader or control board. The written estimate sets the final price. Call (866) 942-8010 for a free estimate.
Keypad and Entry Programming
Codes that quit working are often a programming fault or a failed keypad rather than a wiring problem. We test the keypad, reprogram the entry list, and confirm each code releases the gate as it should.
Readers, Intercoms, and Call Units
A call unit that no longer reaches the house or office can be a board fault, a wiring issue, or a failed module. We trace the circuit and repair the specific component that has dropped out.
Commercial Gate Operator
Commercial Gate Operator repair addresses the heavier duty equipment that runs entry and exit gates for HOAs, offices, and gated properties, where the gate cycles many times an hour and a failure affects a whole group of people. You need it when a commercial operator won’t lift, trips its breaker, or a card reader and gate fall out of sync. We service FAAC, BFT, and DoorKing commercial systems and understand how access control ties into the operator. A typical commercial operator repair in Rochester runs $350-$1,200 depending on the operator and the fault. The written estimate sets the final price. Call (866) 942-8010 for a free estimate.
High-Cycle Wear and Duty Rating
Commercial gates accumulate cycles fast, so gears, brakes, and limit switches wear sooner. We inspect the duty-cycle parts and replace what’s near failure rather than waiting for a breakdown at the worst time.
Access Board Integration
When the operator and the access control board stop talking, the gate can be healthy and still refuse to open. We test both sides and restore the handshake between them.
Brands We Service
We’re factory-familiar with the major gate brands, and that familiarity matters because each system has its own failure patterns and its own diagnostics. We service LiftMaster openers and know where their gear trains and limit switches wear out first. We work on FAAC and BFT systems and understand their boards, their safety edge wiring, and the faults those systems tend to develop. Linear operators are in our regular rotation too, along with Ghost Controls and Mighty Mule for residential gates and DoorKing, Viking, and Elite for commercial and access control work. That breadth means we can diagnose by system and system brand rather than guess at a fix two visits later. Whether you have a LiftMaster operator, a FAAC arm, or any other make, we can help.
Knowing the brand up front shortens the diagnostic and usually means the repair is done on the first visit. We ask what you have when you call, and we check what’s actually failing before we quote. If the system is beyond repair, we’ll tell you plainly, and we can handle a new installation so you’re not calling a second company. That applies to both the residential systems and the commercial access equipment. If you’re still deciding between fixing and replacing, see our Rochester Gate Repair page for the full range of work we handle.
See the difference
Before
After
Before
After
Before
AfterSigns You Need a Pro Right Now
Some gate faults are a nuisance. Others are a real safety and access problem, and a trained technician is the only responsible person to put hands on the motor, wiring, or operator. Here’s what should send you to the phone.
- The gate reverses on its own or won’t close. A safety edge, photo eye, or limit setting is likely at fault. Until it’s checked, the gate can crush against an obstacle instead of stopping, so don’t keep cycling it.
- A burning smell or a tripping breaker. That points to the motor or the control board and to potential power problems. Stop using the gate and have the electrical side tested by a technician.
- Clicking with no movement. A failed board, a dead motor, or a stripped gear produces the same click-and-nothing symptom. Diagnostics tell you which before parts get replaced.
- Stalling halfway through travel. Binding linkage, worn track, or an undersized motor all cause mid-travel stalls and heat the motor. Driving through it repeatedly shortens the motor’s life.
- Keypad codes or remotes quitting intermittently. A dying receiver, a weak keypad, or a corroded connection can leave your gate open at the wrong moment. A controlled test isolates the fault.
Our Process, Step by Step
- 1
We take your call and ask what the gate is doing and what brand system you have. A few questions up front often tell us whether this is a board, a motor, or a mechanical fault before anyone moves.
- 2
We come out, look the gate over, and test the system rather than guess. That means checking motor current draw, limit settings, safety edge trips, and the control board’s fault codes to trace the problem to a specific component.
- 3
We give you a written estimate with the options, including where a repair makes sense and where it doesn’t. The price is quoted and agreed before any work starts, so there’s no invoice surprise at the end.
- 4
We do the repair and then cycle the gate through its full travel several times to confirm it’s right. We test the safety edges and limits after the work, not just before.
- 5
We walk you through what failed and what to watch for, and we’re reachable if anything shifts afterward. If a full replacement is the smarter call, we’ll say so and quote it. For a closer look at the electric side, see our electric gate repair page.
How Much Does Electric Gate Repair Cost in Rochester?
Electric gate repair in Rochester typically runs $180-$900 for the work itself, with commercial operators running higher at $350-$1,200 depending on the system. What drives the range is the component that failed and how far the repair reaches. A board swap is on the lower end, a motor or operator replacement sits higher, and access control faults fall somewhere between. The service call itself is quoted in writing before we touch anything, so you know the number first.
What affects the price: the brand and duty rating of the operator, whether the fault is a single component or a chain of wear, the condition of the gate and its track, and whether we’re repairing or replacing. High-cycle commercial equipment costs more to put right than a residential arm because the parts are built heavier and the diagnosis takes longer. A gate that’s been driven through a fault for weeks often needs more than one repair by the time we see it, which is why calling early is cheaper than calling late.
How to avoid overpaying: get the written estimate before work begins, ask what the diagnostic found, and don’t let anyone replace the whole operator when a board or gear is the actual fault. We’ll tell you when a repair makes sense and when a replacement does. What’s included in a free estimate: the on-site look, the diagnostic, and the written price for the repair we recommend. Call (866) 942-8010 for an exact quote – estimates are free.
Our Service Area Near Rochester
We cover electric gate repair across Rochester and the surrounding towns, including Irondequoit, Gates, Brighton, North Gates, Greece, East Rochester, Spencerport, Fairport, Webster, Hilton, and the neighborhoods around Rochester Institute of Technology. Response times depend on where you are and the day, but same-day service is often available nearby. If you’re a property manager covering several locations, we can talk through scheduling all of them. For more, see our electric gate repair edition.
Serving Rochester, NY – Our Local Coverage Area
We serve Rochester and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions About Electric Gate Repair in Rochester
Electric gate repair is the diagnosis and fix of an automated gate’s operator, motor, control board, safety sensors, and access hardware. It covers everything from the arm or slider unit that moves the gate to the keypad or reader that tells it to open. It’s distinct from mechanical gate repair, which handles hinges, latches, and structural issues on a gate that isn’t powered. If your gate is automatic, the repair almost always involves both elements, and we handle both. Call (866) 942-8010 for a free estimate.
Most electric gate repairs take one to three hours on site, assuming the replacement parts are matched and available. A board swap or a safety sensor fix is often under an hour. A motor or operator replacement takes longer because the gate has to be tested through its full travel afterward. We tell you the expected time when we give the estimate. Call (866) 942-8010 for a free estimate.
Electric gate repair in Rochester typically runs $180-$900, with commercial operator work at $350-$1,200. The price depends on the component that failed, the brand, and whether we’re repairing or replacing. The written estimate sets the final price and is agreed before work starts. Call (866) 942-8010 for an exact quote – estimates are free.
Yes. We service LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule systems. Knowing the brand lets us diagnose by system rather than by guesswork, which is what speeds up a first-visit fix. Tell us what you have when you call so we can be ready. Call (866) 942-8010 for a free estimate.
Same-day service is often available in Rochester, though it depends on the day and how booked we are. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday; we’re closed Saturday. A call outside dispatch hours is booked into the next opening. Call (866) 942-8010 for a free estimate.
We stand behind the repairs we make and the satisfaction guarantee on the work we perform. If something we fixed isn’t right, we’ll make it right. The warranty terms are laid out on the written estimate so you know exactly what’s covered. Call (866) 942-8010 for a free estimate.
Clear access to the gate, the operator, and the control box so the technician can reach everything. Have the brand or model of the operator if you know it, and note when the problem started and what it does. If the gate is stuck, don’t force it – leave it and tell us the symptom. Call (866) 942-8010 for a free estimate.
Schedule Your Electric Gate Repair Service in Rochester Today
Don’t let a gate fault turn into a motor replacement or a security gap. Our gate-only specialists handle the repair, explain what failed, and quote the price before any work starts. For the surrounding area, see our electric gate repair page. Call (866) 942-8010 for a free, no-obligation estimate. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. If you’re thinking about new equipment instead, look at our gate installation service.
Written by the team at Rochester Gate Repair.